ایران شهرساز را در تلگرام دنبال کنید

[-]
[-]

پشتیبانی 09120592515 ایمیل: iranshahrsaz@yahoo.com

[-]
[-]
امتیاز موضوع:
  • 0 رأی - میانگین امتیازات: 0
  • 1
  • 2
  • 3
  • 4
  • 5
1
What Is The Difference Between Mechanical Seal And Oil Seal?
What Is The Difference Between Mechanical Seal And Oil Seal?

    The mechanical seal is used in a pump, mixer and other mechanical engineering scenarios to contain the fluid within a vessel where a shaft rotates through a stationary (or rotating) housing.

    Why is mechanical seal important in this situation?  It is because the rotating shaft has to move in a wet environment, but there should not be the leakage of pressurized fluid. Hence, the role of a seal is quite critical.

    Does it mean the seal stops the leakage completely? Well, on the practical grounds yes because there is no ‘visible leakage’.

    There is a little leakage as the fluid vapors get released into the atmosphere from the faces of the seal, though. Since the quantity is hardly quantifiable, the seals are considered leak proof.

            The seals do not damage pump sleeve or shaft.
       
            Due to inboard springs that get adjusted as the seal faces wear, it is not required to do daily maintenance.
       
            Mechanical seals cause less power consumption than gland packing because of the lightly loaded faces.
       
            In mechanical seals, the lubricant doesn’t get washed out. Therefore, bearing contamination gets avoided in normal operational conditions.
       
            Plant equipment remains corrosion free.
       
            Relatively less maintenance and cleaning are required. It makes mechanical seals cost-effective.
       
            Oil seals prevent accumulation of dirt in the machine.
       
    Oil seals  close off the space between stationary and moving components in the mechanical equipment. It saves the lubricant from escaping through the equipment and ensures smooth operation of the machine.

    Oil seals are called rotary shaft seal or radial lip also.

            Oil seals prevent seeping of potentially hazardous contaminants like dirt or fluid in the running machine
       
            These seals safeguard mixing of two things like oil and water
       
            In the high-intensity work environment, oil seals play a vital role
       
            Oil seals are long-lasting and sturdy
       
            Oil seals can work relentlessly if the preventive and corrective maintenance is in place
       
            Low wear and tear
       
    Types Of Component Mechanical Seals

    Seals and gaskets are sometimes custom-made to service unique applications, but we can group most seals that prevent leakage at the interface of a moving part and a stationary part into eight main types of component mechanical seals.

            Wave Spring Mechanical Seals:  Principally used for liquids of high viscosity, wave spring mechanical seals are popular for pharmaceutical, dairy, brewery and food processing applications. They are often fitted to the shaft with grub screws and in the case of high viscosity media would also have stationaries with anti-rotation pins. Some designs are specially constructed to work in shallow, confined seal housings.
       
            Water Pump Seals:  Because water is such a poor lubricant of seal faces, it is critical that water pump seals use excellent materials for applications such as shower pumps, irrigation, heating systems, swimming pools and spas.
       
            Bellows Mechanical Seals:  Compact, versatile, extremely reliable seals suitable for a wide range of applications. Available with either O Ring Mounted or Boot mounted Stationaries in DIN and Non-Din sizes. Recommended for media containing solids and are widely used in Pumps, mixers, compressors etc.
       
            Diaphragm Seals:  Featuring parallel springs, diaphragm seals are used in very diverse applications including agitators, compressors, mixers, pumps and other rotary shaft equipment. . The diaphragm in the rotary head rotary seals on the shaft so they are not affected by rotational direction.
       
            Balanced Diaphragm Seals:  Similar to Diaphragm seals but are also hydraulically balanced to reduce heat and friction at the seal interface, an innovative patented design protects against seal failure in applications where thin metal drive components are prone to cut into the retainer.
       
            Conical Mechanical Seals:  This is an extremely versatile and popular mechanical seal. Available in a wide range of materials to suit a variety of environments, they are robust and durable. However these seals are rotation dependent and come with either left hand or right hand springs.
       
            Parallel Mechanical Seals:  Parallel seals are a heavy duty single spring seal. They can use different methods of providing the face to the seal and can be supplied with either left- or right-hand wound springs. A good general-purpose seal, they are used in marine pumps, waste-water, pulp and paper and textile applications as well as refrigeration compressors.

            Multi Spring Seals:  Proven effective design, PTFE wedge styles are often used in chemical the chemical industry for arduous applications such as corrosive process fluids.
       
    What is a Double Seal

    Double (or dual) mechanical seals are designed to  ensure maximum sealing safety.  These seals  virtually eliminate leakage of the fluid or gas being handled in pumps or mixers.

            Double seals provide a level of safety/zero emissions compliance not possible with single seals. This is essential when pumping or mixing a dangerous or toxic substance.
       
            Double seals are a must-have for certain applications in many countries
       
            These seals are increasingly used by companies to meet specific environmental goals or emissions requirements.
       
    A properly installed double seal also allows for  near complete control  over the seal operating environment and fluid film over the seal faces. This factor alone can greatly maximize seal life.

    A double mechanical seal has two primary seals with a barrier or buffer fluid area in between. Each primary seal typically consists of a softer, narrower stationary face accompanied by a harder, wider rotating face. This arrangement enables the softer seal to wear while maintaining the integrity of the harder faced seal during service.

    Pump and seal manufacturers recommend double seals for a variety of reasons:

            Prevent a hazardous product from reaching the atmosphere/polluting the environment
       
            Avoid leakage of an expensive process fluid product
       
            Maximize seal life by controlling the type of fluid film on the seal faces
       
            Isolate the mechanical seal from atmospheric conditions
       
            Provide an alternative when the process fluid will not provide stable and reliable lubrication of the seal faces (such as gaseous media, viscous fluids, non-settling slurries, or fluids liable to harden)
       
            Establish a backup seal in the event of an inboard seal failure or planned equipment repair (or to identify seal failure during operation)
       
            Avoid contamination of the process media should one seal fail
       
    Mechanical Seal Questions

    Q:  What is a mechanical seal?

    A:  An end-face mechanical seal is a device used on a rotating shaft to seal fluids. It consists of two flat faces that are installed perpendicular to the shaft. One of the faces is mounted stationary to the seal chamber or housing. The other face rotates with the shaft to provide the primary seal. Axial mechanical force and fluid pressure maintain the contact between the wearable seal face  materials.

    Q:  What is a cartridge seal?

    A:  A cartridge-mounted, end-face mechanical seal (cartridge seal) is a completely self-contained unit that consists of the sealing components, a gland, sleeve, and hardware that allows the unit to be pre-assembled and preset. This feature eases installation and maintenance on rotating equipment on which axial adjustments are  required.

    Q:  What is a component seal?

    A:  Component, end-face mechanical seals (a  component seal) consist of a separate rotating member and stationary seat that mount in a gland or housing. Since they are not preset, installation and maintenance are generally more difficult requiring experienced technicians to properly install and adjust  them.

    Q:  What is an air seal?

    A:  Air seals  are non-contacting, pneumatic devices engineered for sealing rotating shafts. They protect against product loss, emissions, and contamination by using small amounts of air or inert gas that is throttled to create positive pressure and an effective  seal.

    Metal Bellows

    A metal bellows is a precision-engineered, flexible metal component that acts as a leak-tight seal– effectively separating two environments from one another. These versatile parts can convert changes in pressure, temperature, and position into linear motion and be used for rotary transmission that maintains flexible mechanical and electrical connections.

    Metal bellows products are used in a wide variety of industrial and mechanical applications and are designed to compress, extend, or bend to absorb axial and angular movement. Some examples of useful applications for metal bellows include actuators, beamlines, expansion joints, mechanical seals, pumps, valve seals, thermal expansion tanks, reservoirs, and more.
Metal bellows are available from MW Components in three varieties, which are differentiated by their fabrication method; these include edge-welded bellows, electrodeposited bellows, and hydroformed bellows. MW Components produces precision custom metal bellows using all three of these fabrication methods.

آخرین ارسال های من :
موضوع‌های مشابه…
موضوع نویسنده بازدید آخرین ارسال
  Difference Between Fusion Welding and Solid State Welding nhgjmyrr 75 ۱۴۰۱-۳-۲۳، ۰۶:۴۸ صبح
آخرین ارسال: nhgjmyrr
کاربرانِ درحال بازدید از این موضوع: 1 مهمان
آمار انجمن
آخرين ارسال ها
موضوع تاريخ, زمان  نويسنده آخرين ارسال کننده انجمن
  سرفصل ارزیابی اثرات توسعه بر محیط زیست ۵-۲۳ m.marziye mymymym ارزیابی اثرات توسعه بر محیط زیست
  سرفصل حقوق و قوانین شهرسازی ۵-۲۳ m.marziye mymymym حقوق و قوانین شهرسازی
  لینک های دانلود کتاب های مفید شهرسازی مناسب برای کنکور ۵-۱۸ E.Y.I waboq اطلاعیه ها
  مهندس romisa برنده هفته سوم:تخفیف 50 درصدی پکیج ها برای فعالترین کاربر هفته ۵-۱۸ romisa waboq اطلاعیه ها
  Diablo 2: Resurrected players must first remove the old gems ۵-۱۴ bertramuzi bertramuzi اخبار مسکن مهر و مرتبط
  Madden 23 made its way to Xbox Game Pass a few months after its launch ۵-۱۴ bertramuzi bertramuzi gis
  RuneScape 3 has changed a lot from the way RuneScape used to be ۵-۱۴ bertramuzi bertramuzi تالار گفتمان طراحی شهری
  من نمیتونم مطلب ارسال کنم گویا مشکلی برای سایت پیش امده ۵-۱۰ s1s2s3 ghavampol آموزش ارسال مطلب و مشکلات ارسال فایل
  مصاحبه اختصاصی سایت ایران شهرساز با رتبه 29 کشور در گرایش طراحی شهری 95 ۵-۳ alireza waboq تالار گفتمان طراحی شهری
  از بچه های گلستان ،شهر گنبد کسی هس ؟؟؟؟؟؟ ۵-۳ raoof waboq کارگاره هم اندیشی
  نکات انتقال اتوکد به رویت ۵-۲ alireza pewiryce تالار گفتمان معماری
  دانلود فیلم آموزش ضوابط کاربردی آزمون طراحی نظام مهندسی معماری مدرس صدیق ۵-۲ memar1394 pewiryce تالار گفتمان معماری
  جزئیات ثبت نام قبول شدگان در دوره ارشد دانشگاه آزاد 97 اعلام شد ۵-۱ Sahab pewiryce اخبار دانشگاه
  نحوه عودت وجه ثبت نام داوطلبان دانشگاه آزاد 96 این هفته اعلام می شود ۵-۱ Sahab pewiryce اخبار دانشگاه
  فروش کتاب تاریخ شکل شهر(جیمز موریس) ۴-۳۰ alireza mymymym کتاب های برنامه ریزی شهری
با ارسال فایل و شرکت در موضوعات ایجاد شده و پاسخ به آنها ما را همراهی کنید.

[-]
جستجو
جستجوی گوگل